EvoXForums.com - Mitsubishi Lancer Evolution X Forums - Reply to Topic
EvoXForums.com - Mitsubishi Lancer Evolution X Forums
Go Back   EvoXForums.com - Mitsubishi Lancer Evolution X Forums > Evo X > Evo X Transmission & S-AWC System > S-AWC System > AYC Pump Motor keeps burning out.
Home Register Forum Store Members List Calendar Auto Loans vBGarage Photo Gallery Search Today's Posts Mark Forums Read Auto EscrowInsurance

S-AWC System For discussion of the S-AWC system and it's components including (but not limited to) driveshafts, differentials, programming, etc.

Thread: AYC Pump Motor keeps burning out. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the EvoXForums.com - Mitsubishi Lancer Evolution X Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Security Question
While balancing on a piece of wood, two inches by four inches known as a 2x4, john and his friend sally both spotted a dalmatian inside a truck with sirens, headed to put out a fire. State what the 2x4 is made of.
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-26-2019 02:37 PM
Wertigo
Quote:
Originally Posted by tricky1024 View Post
hopefully someone can help me out here as i am now pulling my hair out with an issue with the AYC pump in a FQ300 SST. the pump died in January and seems the previous owner did a job on a frankinpump with a really odd motor.

either way the motor and pump where beyond help so i bough a complete refurb unit and installed.

now everytime i install the unit i bleed the system using the bleed tool you connect to the solenoids and manually bleed the system.

i start the car and hear the motor kick in/prime and turn off after 3/5 seconds, no lights on the dash. i drive 3 miles down the road and the motor dies and burns out. i have now had the motor re-built 5 times.

i am starting the think there must be another issue, maybe ayc computer or wiring but have no idea, anyone ever seen this and can you point me in the right direction?

you are jamming the engine at the moment of pressure build-up. as when pressure is set the load on the shaft increases. you could also have a skewed pump and gear
04-24-2019 01:42 AM
turismolover22 I bet if you just got a whole harness from a part out that it would likely fix your issue
04-23-2019 05:24 PM
2x4 http://www.evoxservicemanual.co.uk/
04-23-2019 11:14 AM
tricky1024 i dont, i will see if i can get one. thank you.
04-20-2019 11:16 AM
misdeismo Uea, definitely seems like an electrical issue. Do you have the service manual? Probably would be a big help looking at the electrical schematic.
04-17-2019 12:44 PM
tricky1024 so when i first started (5 pumps ago now) the main wiring harness to the motor was competed melted and shot, so much so i have had to change the main motor connector to a Anderson type connector on the car side of the loom.

any idea of where i should start looking? boot?
04-16-2019 10:26 PM
Yxd68 Time to call a priest??
04-16-2019 07:41 PM
turismolover22
Quote:
Originally Posted by tricky1024 View Post
hopefully someone can help me out here as i am now pulling my hair out with an issue with the AYC pump in a FQ300 SST. the pump died in January and seems the previous owner did a job on a frankinpump with a really odd motor.

either way the motor and pump where beyond help so i bough a complete refurb unit and installed.

now everytime i install the unit i bleed the system using the bleed tool you connect to the solenoids and manually bleed the system.

i start the car and hear the motor kick in/prime and turn off after 3/5 seconds, no lights on the dash. i drive 3 miles down the road and the motor dies and burns out. i have now had the motor re-built 5 times.

i am starting the think there must be another issue, maybe ayc computer or wiring but have no idea, anyone ever seen this and can you point me in the right direction?
If the motor is burning up like that, you're going to have to start chasing electrical.

It sounds like there is a short somewhere and it is activating it when it shouldn't be and burning it up
04-15-2019 01:28 PM
tricky1024
AYC Pump Motor keeps burning out.

hopefully someone can help me out here as i am now pulling my hair out with an issue with the AYC pump in a FQ300 SST. the pump died in January and seems the previous owner did a job on a frankinpump with a really odd motor.

either way the motor and pump where beyond help so i bough a complete refurb unit and installed.

now everytime i install the unit i bleed the system using the bleed tool you connect to the solenoids and manually bleed the system.

i start the car and hear the motor kick in/prime and turn off after 3/5 seconds, no lights on the dash. i drive 3 miles down the road and the motor dies and burns out. i have now had the motor re-built 5 times.

i am starting the think there must be another issue, maybe ayc computer or wiring but have no idea, anyone ever seen this and can you point me in the right direction?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 03:12 AM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.1 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.